THERMADOR Error Code F0
Professional Ranges Models: PDR30/36/48…PRG30/36/48
| ERROR CODE | DESCRIPTION | RESOLUTION |
| CODE F0 | Internal logic failure; cancel key supervision. Sounds alarm and resets to non-cook mode | Repair the electronic range control (also called clock or ERC) |
The control constantly keeps track of system parameters for control and also oven failures and reports a fault code when a system problem is identified. The control utilizes the stoves blue “on light” and also oven “heating light” to report an identified fault code. The control will certainly remain to blink the lights in the suitable sequence as long as the mistake exists.
Discovery of a mistake does not hinder the capacity of the control to continue to function if the mistake is not critical for the desired procedure. For instance: If the array door lock is defective, the array will remain to cook given that the mistake would just stop the range from self-cleaning.
HOW TO ANALYZE CODES
When a mistake takes place, the control will certainly blink the blue stove “on light” and heaven “home heating light” sequentially to suggest the mistake. The fault codes have two numbers, these numbers are translated by the number of times the lights flash. The oven “on light” will certainly blink indicating the first number, and also the “heating light” will blink showing the second number.
INSTANCE:
Mistake E9 is … No Cooling Followers. The code is 43. The oven “on light” will flash 4 times, after that the “heating light” will flash three times, after that pause. The sequence will certainly then duplicate as long as the fault exists.
ERROR CODES FOR OVENS WITH DREEFS CONTROL
The adhering to graph reveals the mistake codes that can be presented in the Oven/Selector home window throughout details stove breakdowns. Some of the error messages can be gotten rid of by carrying out the complying with actions:
- Transform the selector handle to OFF
2.”Fine-tune” the oven by transforming the selector knob somewhat to the left (counterclockwise). This may stop the blinking message/beeping and also clear the home window. - For mistakes E1, E9, E11, E12 and E13, the power supply mosting likely to the even need to be shut off briefly, as well as back on again.
- If an error remains presented when the selector button is OFF, and after trying to get rid of the screen, as displayed in steps 2 as well as 3, turn off the power going to the stove, and describe the chart below to help you locate the problem.
| ERROR CODE | NOTE | CHECK REPAIR |
| F0 | Internal logic failure; cancel key supervision. Sounds alarm and resets to non-cook mode | Replace the electronic range control (also called clock or ERC) |
| F1 | Internal logic failure (monitoring function). Sounds alarm and inhibits cook modes | Replace the electronic range control (also called clock or ERC) |
| F2 | Temperature runaway detected (Bake/Broil: 600 – 700 F; Clean: 930 – 1000 degrees F). Sounds alarm and resets to non-cook mode. Check relay board for stuck contacts. Check oven temperature sensor for normal room temperature resistance (1085-1097 ohms at 75 degrees F). Check sensor wiring connectors for a loose or high resistance connection. Check electronic range control (also called clock or ERC) functions | Replace relay board if necessary. Replace oven temperature sensor if other components check normal. If failure repeats, replace electronic range control (also called clock or ERC) |
| F3 | Open circuit detected; oven temperature sensor. Check sensor for normal room temperature resistance (1085-1097 ohms at 75 degrees F). Check wires and connections between electronic range control (also called clock or ERC) and oven temperature sensor | Replace sensor if other components check normal. Replace electronic range control (also called clock or ERC) if fail code reoccurs |
| F4 | Short circuit detected; oven temperature sensor. Check sensor for normal room temperature resistance (1085-1097 ohms at 75 degrees F). Check wires between electronic range control (also called clock or ERC) and sensor. | Replace sensor if other components check normal. Replace electronic range control (also called clock or ERC) if fail code reoccurs |
| F7 | Function key shorted for over 16 seconds. Check for something pressing a key or preventing normal release of the key | Replace electronic range control (also called clock or ERC) if other components check normal |
| F8 | Internal logic failure; calibration. Alarm sounds and resets to non-cook mode. Check oven temperature sensor for normal room temperature resistance (1085-1097 ohms at 75 F). Check wires and connections between electronic range control (also called clock or ERC) and oven temperature sensor | Replace electronic range control (also called clock or ERC) and oven temperature sensor if other components check normal |
| F9 | Internal logic ailure; door latch supervision. Alarm sounds and resets to non-cook mode. If door is locked due to clean temperatures, disconnect power until door can be unlocked | Replace the electronic range control (also called clock or ERC) |
| Fd | Bake & Broil relay drives active simultaneously. Check relay board for damage: trace E6 to K2 & K3, and burned contacts K3 & K3 | Replace electronic range control (also called clock or ERC). Replace relay board if necessary |
| Blank Display | No power to lectronic range control (also called clock or ERC). Check oven light and cooktop dial lights (powered by L2 & L1, respectively). Check relay board transformer primary, E1 to E2 (140 ohms typical). If the transformer internal fuse is still OK, check output voltages, pins 9 – 8 (3.2 v.a.c.) and 7 – 6 (21 v.a.c.). Check clock functions after replacing relay board | If relay board transformer open (E1 to E2), replace relay board. If still no clock functions replace electronic range control (also called clock or ERC) |
| ERROR CODE | NOTES |
| A | Turns heat off on the failed oven only; microwave not affected. |
| B | Turns all heat off; microwave not affected. |
| C | Disables the CLEAN mode in both ovens; allows COOK and microwave. |
| D | Error will remain in the display until oven is repaired and powered back up. No error tones. |
| E | Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN. |
| F | Tweaking clears to “—“ for retry. |
| G | Clears when the oven temperature is less then the runaway temperature with the selector switch off. |
| H | Can be cancelled by tweaking if a good sensor is detected. |
| I | Cleared with a mode change. |
| J | Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door. |
| K | Turns heat and microwave off. |
| L | If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message. |