THERMADOR Error Code E9
Professional Ranges Models: PDR30/36/48…PRG30/36/48
ERROR CODE | DESCRIPTION | RESOLUTION |
CODE E9 | Turn the clock selector knob to OFF Adjust the oven control by turning the clock selector knob slightly to the left (counter clockwise). This may stop the flashing message/beeping and clear the display window. | Latch switch problems |
The control constantly keeps track of system parameters for control and also stove failures and reports a mistake code when a system issue is detected. The control makes use of the ovens blue “on light” as well as oven “home heating light” to report a discovered mistake code. The control will continue to flash the lights in the appropriate sequence as long as the fault exists.
Discovery of a mistake does not impede the capacity of the control to continue to operate if the fault is not critical for the designated procedure. For instance: If the variety door lock is defective, the variety will certainly continue to prepare given that the mistake would only avoid the variety from self-cleaning.
HOW TO ANALYZE CODES
When a fault takes place, the control will flash heaven oven “on light” and also heaven “home heating light” sequentially to indicate the fault. The fault codes have 2 numbers, these numbers are analyzed by the variety of times the lights flash. The stove “on light” will blink suggesting the very first number, and the “heating light” will certainly flash indicating the second number.
INSTANCE:
Mistake E9 is … No Cooling Fans. The code is 43. The stove “on light” will certainly flash four times, after that the “home heating light” will certainly flash 3 times, after that time out. The sequence will certainly after that duplicate as long as the fault is present.
ERROR CODES FOR STOVES WITH DREEFS CONTROL
The adhering to graph shows the error codes that can be displayed in the Oven/Selector window throughout certain stove malfunctions. Several of the error messages can be gotten rid of by carrying out the complying with actions:
- Transform the selector knob to OFF
2.”Fine-tune” the oven by turning the selector knob a little to the left (counterclockwise). This may stop the blinking message/beeping and clear the window. - For mistakes E1, E9, E11, E12 and E13, the power supply going to the also have to be turned off momentarily, and also back on again.
- If a mistake stays presented when the selector button is OFF, and after attempting to get rid of the display screen, as displayed in actions 2 as well as 3, switch off the power going to the stove, and describe the graph below to help you find the issue.
ERROR MESSAGE | ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
E1 | C&E | Control board problem. |
E2 | G&K | Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F). |
E3 | A&H | Open oven temperature sensor (>5000 Ω). |
E4 | A&H | Shorted oven temperature sensor (<5000 Ω). |
E5 | K&D | Control board too cold, too hot, or defective. |
E6 | C&J | Control board problem. |
E7 | A&I | Illegal temperature display. Turn off oven and try again. |
E8 | A&D | Control board problem. |
E9 | A&E | Latch switch problem. |
E10 | B&D | Control board problem. |
E11 | A&F | CT oven – latch switch problem |
E12 | A&E | CT ovens – latch switch problem |
E13 | A&C | CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data). |
E14 | A&E | Latch switch problem. |
E15 | B&D | Control board problem. |
ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
A | Turns heat off on the failed oven only; microwave not affected. |
B | Turns all heat off; microwave not affected. |
C | Disables the CLEAN mode in both ovens; allows COOK and microwave. |
D | Error will remain in the display until oven is repaired and powered back up. No error tones. |
E | Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN. |
F | Tweaking clears to “—“ for retry. |
G | Clears when the oven temperature is less then the runaway temperature with the selector switch off. |
H | Can be cancelled by tweaking if a good sensor is detected. |
I | Cleared with a mode change. |
J | Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door. |
K | Turns heat and microwave off. |
L | If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message. |