THERMADOR Error Code E7
Professional Ranges Models: PDR30/36/48…PRG30/36/48
ERROR CODE | DESCRIPTION | RESOLUTION |
CODE E7 | Turns heat off on failed oven only, micro not affected. Cleared with a mode change. | Illegal temp display turn off and retry |
The control continuously checks system parameters for control as well as oven failings and reports a mistake code when a system issue is found. The control utilizes the stoves blue “on light” and oven “home heating light” to report a discovered fault code. The control will certainly continue to blink the lights in the appropriate series as long as the mistake exists.
Discovery of a mistake does not impede the ability of the control to remain to function if the mistake is not critical for the intended operation. As an example: If the variety door lock is defective, the range will certainly continue to prepare considering that the fault would only protect against the array from self-cleaning.
HOW TO ANALYZE CODES
When a fault happens, the control will blink heaven oven “on light” as well as the Blue “heating light” sequentially to show the fault. The mistake codes have two numbers, these numbers are translated by the variety of times the lights flash. The stove “on light” will certainly blink indicating the first number, and also the “home heating light” will blink suggesting the second number.
INSTANCE:
Error E9 is … No Cooling Followers. The code is 43. The oven “on light” will certainly flash four times, after that the “home heating light” will blink 3 times, then pause. The series will certainly after that repeat as long as the mistake is present.
ERROR CODES FOR STOVES WITH DREEFS CONTROL
The complying with chart reveals the error codes that can be displayed in the Oven/Selector window throughout certain oven breakdowns. Several of the mistake messages can be gotten rid of by doing the complying with actions:
- Turn the selector knob to OFF
2.”Modify” the oven by turning the selector handle somewhat to the left (counterclockwise). This might stop the flashing message/beeping and also clear the window. - For mistakes E1, E9, E11, E12 and also E13, the power supply mosting likely to the also must be shut off momentarily, and back on once again.
- If a mistake continues to be shown when the selector button is OFF, as well as after attempting to remove the display, as received steps 2 as well as 3, turn off the power mosting likely to the stove, and describe the graph listed below to help you find the issue.
ERROR MESSAGE | ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
E1 | C&E | Control board problem. |
E2 | G&K | Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F). |
E3 | A&H | Open oven temperature sensor (>5000 Ω). |
E4 | A&H | Shorted oven temperature sensor (<5000 Ω). |
E5 | K&D | Control board too cold, too hot, or defective. |
E6 | C&J | Control board problem. |
E7 | A&I | Illegal temperature display. Turn off oven and try again. |
E8 | A&D | Control board problem. |
E9 | A&E | Latch switch problem. |
E10 | B&D | Control board problem. |
E11 | A&F | CT oven – latch switch problem |
E12 | A&E | CT ovens – latch switch problem |
E13 | A&C | CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data). |
E14 | A&E | Latch switch problem. |
E15 | B&D | Control board problem. |
ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
A | Turns heat off on the failed oven only; microwave not affected. |
B | Turns all heat off; microwave not affected. |
C | Disables the CLEAN mode in both ovens; allows COOK and microwave. |
D | Error will remain in the display until oven is repaired and powered back up. No error tones. |
E | Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN. |
F | Tweaking clears to “—“ for retry. |
G | Clears when the oven temperature is less then the runaway temperature with the selector switch off. |
H | Can be cancelled by tweaking if a good sensor is detected. |
I | Cleared with a mode change. |
J | Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door. |
K | Turns heat and microwave off. |
L | If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message. |