THERMADOR Error Code E6
Professional Ranges Models: PDR30/36/48…PRG30/36/48
ERROR CODE | DESCRIPTION | RESOLUTION |
CODE E5 | Disables clean mode in both ovens, allows cook and microwave. Can be tweaked away for retry. User must unlatch and delete the “—” to try to re-latch the door. | Repair the electronic range control (also called clock or ERC) |
The control constantly checks system specifications for control and also oven failings and reports a fault code when a system issue is identified. The control uses the ovens blue “on light” and also oven “home heating light” to report a discovered fault code. The control will certainly remain to flash the lights in the ideal sequence as long as the fault exists.
Detection of a mistake does not impede the capacity of the control to remain to work if the mistake is not critical for the intended operation. For example: If the variety door latch is defective, the variety will remain to prepare given that the fault would only stop the array from self-cleaning.
HOW TO ANALYZE CODES
When a mistake takes place, the control will flash heaven oven “on light” and also heaven “heating light” sequentially to indicate the mistake. The mistake codes have 2 numbers, these numbers are translated by the number of times the lights blink. The stove “on light” will flash suggesting the very first number, and also the “home heating light” will blink showing the second number.
EXAMPLE:
Error E9 is … No Cooling Fans. The code is 43. The oven “on light” will certainly flash 4 times, then the “home heating light” will flash 3 times, after that pause. The series will certainly after that duplicate as long as the fault is present.
MISTAKE CODES FOR STOVES WITH DREEFS CONTROL
The adhering to graph reveals the error codes that can be presented in the Oven/Selector home window during details stove breakdowns. Several of the error messages can be cleared by doing the complying with actions:
- Turn the selector knob to OFF
2.”Tweak” the stove by turning the selector handle a little to the left (counterclockwise). This might stop the flashing message/beeping and also clear the home window. - For mistakes E1, E9, E11, E12 and also E13, the power supply mosting likely to the even should be shut off for a short time, and back on again.
- If an error continues to be displayed when the selector button is OFF, and also after attempting to remove the screen, as displayed in steps 2 and also 3, switch off the power mosting likely to the oven, and also refer to the graph listed below to assist you find the trouble.
ERROR MESSAGE | ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
E1 | C&E | Control board problem. |
E2 | G&K | Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F). |
E3 | A&H | Open oven temperature sensor (>5000 Ω). |
E4 | A&H | Shorted oven temperature sensor (<5000 Ω). |
E5 | K&D | Control board too cold, too hot, or defective. |
E6 | C&J | Control board problem. |
E7 | A&I | Illegal temperature display. Turn off oven and try again. |
E8 | A&D | Control board problem. |
E9 | A&E | Latch switch problem. |
E10 | B&D | Control board problem. |
E11 | A&F | CT oven – latch switch problem |
E12 | A&E | CT ovens – latch switch problem |
E13 | A&C | CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data). |
E14 | A&E | Latch switch problem. |
E15 | B&D | Control board problem. |
ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
A | Turns heat off on the failed oven only; microwave not affected. |
B | Turns all heat off; microwave not affected. |
C | Disables the CLEAN mode in both ovens; allows COOK and microwave. |
D | Error will remain in the display until oven is repaired and powered back up. No error tones. |
E | Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN. |
F | Tweaking clears to “—“ for retry. |
G | Clears when the oven temperature is less then the runaway temperature with the selector switch off. |
H | Can be cancelled by tweaking if a good sensor is detected. |
I | Cleared with a mode change. |
J | Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door. |
K | Turns heat and microwave off. |
L | If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message. |