THERMADOR Error Code E5 – How to fix? by ApplianceRepairNewYork.us

THERMADOR Error Code E5
Professional Ranges Models: PDR30/36/48…PRG30/36/48

ERROR CODE	DESCRIPTION	RESOLUTION
CODE E5	Turns all heat and micro off. Error will remain in display until repaired and powered up. No error tones.	Control board too cold or too hot, repair the electronic range control (also called clock or ERC)

The control continuously keeps an eye on system criteria for control as well as stove failures as well as reports a fault code when a system trouble is spotted. The control makes use of the ovens blue “on light” and also oven “heating light” to report an identified mistake code. The control will certainly continue to blink the lights in the proper series as long as the mistake exists.

Detection of a mistake does not prevent the capability of the control to continue to function if the mistake is not important for the intended procedure. For instance: If the range door latch is defective, the variety will certainly remain to cook since the mistake would only protect against the array from self-cleaning.

HOW TO INTERPRET CODES
When a fault takes place, the control will flash the blue oven “on light” and heaven “home heating light” sequentially to indicate the fault. The fault codes have two numbers, these numbers are analyzed by the variety of times the lights blink. The stove “on light” will blink showing the very first number, and the “home heating light” will blink suggesting the 2nd number.

INSTANCE:
Error E9 is … No Air conditioning Followers. The code is 43. The stove “on light” will flash four times, after that the “home heating light” will blink 3 times, after that time out. The series will after that duplicate as long as the mistake is present.

MISTAKE CODES FOR STOVES WITH DREEFS CONTROL
The following chart reveals the mistake codes that can be shown in the Oven/Selector home window during specific oven breakdowns. Several of the error messages can be gotten rid of by carrying out the adhering to steps:

Turn the selector handle to OFF
2.”Modify” the stove by turning the selector knob a little to the left (counterclockwise). This might stop the blinking message/beeping as well as clear the home window.
For errors E1, E9, E11, E12 and E13, the power supply mosting likely to the even should be shut off for a little while, and also back on again.
If an error remains shown when the selector button is OFF, and after trying to get rid of the screen, as displayed in actions 2 and also 3, turn off the power going to the stove, as well as refer to the graph below to assist you find the trouble.

ERROR MESSAGE	ERROR CODE NOTES	DESCRIPTION OF PROBLEM
E1	C&E	Control board problem.
E2	G&K	Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F).
E3	A&H	Open oven temperature sensor (>5000 Ω).
E4	A&H	Shorted oven temperature sensor (<5000 Ω).
E5	K&D	Control board too cold, too hot, or defective.
E6	C&J	Control board problem.
E7	A&I	Illegal temperature display. Turn off oven and try again.
E8	A&D	Control board problem.
E9	A&E	Latch switch problem.
E10	B&D	Control board problem.
E11	A&F	CT oven – latch switch problem
E12	A&E	CT ovens – latch switch problem
E13	A&C	CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data).
E14	A&E	Latch switch problem.
E15	B&D	Control board problem.

ERROR CODE NOTES	DESCRIPTION OF PROBLEM
A	Turns heat off on the failed oven only; microwave not affected.
B	Turns all heat off; microwave not affected.
C	Disables the CLEAN mode in both ovens; allows COOK and microwave.
D	Error will remain in the display until oven is repaired and powered back up. No error tones.
E	Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN.
F	Tweaking clears to “—“ for retry.
G	Clears when the oven temperature is less then the runaway temperature with the selector switch off.
H	Can be cancelled by tweaking if a good sensor is detected.
I	Cleared with a mode change.
J	Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door.
K	Turns heat and microwave off.
L	If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message.