THERMADOR Error Code E3
Professional Ranges Models: PDR30/36/48…PRG30/36/48
ERROR CODE | DESCRIPTION | RESOLUTION |
CODE E3 | Turns heat off on failed oven only, micro not affected. Can be cancelled by tweaking if a good oven temperature sensor is detected. | Open oven temperature sensor (over 5000 ohms) |
The control continually checks system specifications for control as well as stove failings as well as reports a fault code when a system issue is detected. The control uses the ovens blue “on light” as well as oven “home heating light” to report an identified fault code. The control will continue to flash the lights in the proper series as long as the fault exists.
Detection of a mistake does not prevent the capability of the control to remain to operate if the fault is not vital for the desired procedure. For example: If the variety door lock is inoperative, the variety will remain to prepare because the fault would only protect against the range from self-cleaning.
HOW TO INTERPRET CODES
When a fault happens, the control will flash the blue oven “on light” as well as heaven “home heating light” sequentially to indicate the fault. The mistake codes have two numbers, these numbers are interpreted by the number of times the lights flash. The oven “on light” will certainly blink showing the initial number, and also the “home heating light” will blink indicating the 2nd number.
INSTANCE:
Error E9 is … No Air conditioning Followers. The code is 43. The oven “on light” will blink 4 times, after that the “home heating light” will certainly flash 3 times, then pause. The series will after that duplicate as long as the fault exists.
ERROR CODES FOR STOVES WITH DREEFS CONTROL
The complying with chart reveals the error codes that can be presented in the Oven/Selector home window throughout particular oven breakdowns. Some of the error messages can be gotten rid of by doing the following steps:
- Turn the selector knob to OFF
2.”Modify” the oven by turning the selector handle a little to the left (counterclockwise). This might quit the flashing message/beeping and also clear the window. - For errors E1, E9, E11, E12 and E13, the power supply going to the also should be turned off momentarily, and back on once more.
- If a mistake stays displayed when the selector switch is OFF, and also after trying to remove the screen, as received actions 2 and also 3, turn off the power going to the oven, and describe the graph listed below to assist you find the issue.
ERROR MESSAGE | ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
E1 | C&E | Control board problem. |
E2 | G&K | Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F). |
E3 | A&H | Open oven temperature sensor (>5000 Ω). |
E4 | A&H | Shorted oven temperature sensor (<5000 Ω). |
E5 | K&D | Control board too cold, too hot, or defective. |
E6 | C&J | Control board problem. |
E7 | A&I | Illegal temperature display. Turn off oven and try again. |
E8 | A&D | Control board problem. |
E9 | A&E | Latch switch problem. |
E10 | B&D | Control board problem. |
E11 | A&F | CT oven – latch switch problem |
E12 | A&E | CT ovens – latch switch problem |
E13 | A&C | CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data). |
E14 | A&E | Latch switch problem. |
E15 | B&D | Control board problem. |
ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
A | Turns heat off on the failed oven only; microwave not affected. |
B | Turns all heat off; microwave not affected. |
C | Disables the CLEAN mode in both ovens; allows COOK and microwave. |
D | Error will remain in the display until oven is repaired and powered back up. No error tones. |
E | Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN. |
F | Tweaking clears to “—“ for retry. |
G | Clears when the oven temperature is less then the runaway temperature with the selector switch off. |
H | Can be cancelled by tweaking if a good sensor is detected. |
I | Cleared with a mode change. |
J | Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door. |
K | Turns heat and microwave off. |
L | If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message. |