THERMADOR Error Code E15
Professional Ranges Models: PDR30/36/48…PRG30/36/48
ERROR CODE | DESCRIPTION | RESOLUTION |
CODE E15 | Turns all heat off, micro not affected. Error will remain in display until repaired and powered up. No error tones. | Repair the electronic range control (also called clock or ERC) |
The control continually checks system criteria for control as well as stove failings as well as reports a mistake code when a system trouble is discovered. The control utilizes the stoves blue “on light” as well as oven “heating light” to report an identified mistake code. The control will certainly continue to blink the lights in the ideal series as long as the fault exists.
Detection of a mistake does not hinder the ability of the control to remain to operate if the fault is not vital for the desired operation. For instance: If the array door lock is defective, the variety will continue to cook given that the fault would just stop the variety from self-cleaning.
HOW TO ANALYZE CODES
When a fault occurs, the control will certainly flash the blue stove “on light” and the Blue “heating light” sequentially to suggest the fault. The fault codes have two numbers, these numbers are analyzed by the variety of times the lights flash. The oven “on light” will certainly flash showing the first number, as well as the “heating light” will blink showing the 2nd number.
EXAMPLE:
Error E9 is … No Cooling Fans. The code is 43. The stove “on light” will flash 4 times, after that the “home heating light” will certainly flash three times, then time out. The sequence will certainly after that duplicate as long as the mistake exists.
MISTAKE CODES FOR STOVES WITH DREEFS CONTROL
The complying with chart shows the mistake codes that can be shown in the Oven/Selector home window throughout specific oven breakdowns. A few of the mistake messages can be removed by executing the following steps:
- Transform the selector handle to OFF
2.”Fine-tune” the stove by transforming the selector knob slightly to the left (counterclockwise). This may quit the blinking message/beeping and also clear the home window. - For mistakes E1, E9, E11, E12 and also E13, the power supply mosting likely to the also have to be turned off for a moment, as well as back on again.
- If an error stays shown when the selector switch is OFF, and also after attempting to remove the display screen, as shown in actions 2 and 3, turn off the power mosting likely to the stove, and describe the chart below to aid you find the issue.
ERROR MESSAGE | ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
E1 | C&E | Control board problem. |
E2 | G&K | Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F). |
E3 | A&H | Open oven temperature sensor (>5000 Ω). |
E4 | A&H | Shorted oven temperature sensor (<5000 Ω). |
E5 | K&D | Control board too cold, too hot, or defective. |
E6 | C&J | Control board problem. |
E7 | A&I | Illegal temperature display. Turn off oven and try again. |
E8 | A&D | Control board problem. |
E9 | A&E | Latch switch problem. |
E10 | B&D | Control board problem. |
E11 | A&F | CT oven – latch switch problem |
E12 | A&E | CT ovens – latch switch problem |
E13 | A&C | CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data). |
E14 | A&E | Latch switch problem. |
E15 | B&D | Control board problem. |
ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
A | Turns heat off on the failed oven only; microwave not affected. |
B | Turns all heat off; microwave not affected. |
C | Disables the CLEAN mode in both ovens; allows COOK and microwave. |
D | Error will remain in the display until oven is repaired and powered back up. No error tones. |
E | Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN. |
F | Tweaking clears to “—“ for retry. |
G | Clears when the oven temperature is less then the runaway temperature with the selector switch off. |
H | Can be cancelled by tweaking if a good sensor is detected. |
I | Cleared with a mode change. |
J | Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door. |
K | Turns heat and microwave off. |
L | If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message. |