THERMADOR Error Code E12 – How to fix? by ApplianceRepairNewYork.us

THERMADOR Error Code E12
Professional Ranges Models: PDR30/36/48…PRG30/36/48

ERROR CODE	DESCRIPTION	RESOLUTION
CODE E12	Turn the clock selector knob to Off Adjust the oven control by turning the clock selector knob slightly to the left (counter clockwise). This may stop the flashing message/beeping and clear the display window.	CT oven; latch switch problem

The control continually checks system parameters for control as well as stove failings and reports a mistake code when a system problem is detected. The control makes use of the ovens blue “on light” as well as oven “heating light” to report a detected mistake code. The control will continue to blink the lights in the appropriate series as long as the fault exists.

Discovery of a mistake does not prevent the ability of the control to remain to function if the fault is not crucial for the designated operation. For example: If the array door lock is faulty, the array will certainly remain to prepare considering that the fault would only avoid the variety from self-cleaning.

HOW TO INTERPRET CODES
When a fault happens, the control will certainly flash heaven oven “on light” and the Blue “home heating light” sequentially to indicate the mistake. The mistake codes have two numbers, these numbers are interpreted by the variety of times the lights blink. The oven “on light” will blink indicating the first number, and the “home heating light” will certainly flash suggesting the second number.

EXAMPLE:
Mistake E9 is … No Air conditioning Followers. The code is 43. The oven “on light” will flash four times, then the “heating light” will flash three times, then pause. The series will certainly then duplicate as long as the fault exists.

ERROR CODES FOR STOVES WITH DREEFS CONTROL
The adhering to chart shows the mistake codes that can be displayed in the Oven/Selector window during certain stove malfunctions. A few of the error messages can be cleared by performing the complying with steps:

Turn the selector knob to OFF
2.”Modify” the stove by turning the selector handle somewhat to the left (counterclockwise). This may quit the blinking message/beeping and clear the home window.
For mistakes E1, E9, E11, E12 and E13, the power supply mosting likely to the even should be turned off momentarily, as well as back on again.
If an error remains presented when the selector switch is OFF, and also after attempting to remove the display screen, as received actions 2 and also 3, turn off the power going to the oven, as well as refer to the chart listed below to aid you locate the trouble.

ERROR MESSAGE	ERROR CODE NOTES	DESCRIPTION OF PROBLEM
E1	C&E	Control board problem.
E2	G&K	Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F).
E3	A&H	Open oven temperature sensor (>5000 Ω).
E4	A&H	Shorted oven temperature sensor (<5000 Ω).
E5	K&D	Control board too cold, too hot, or defective.
E6	C&J	Control board problem.
E7	A&I	Illegal temperature display. Turn off oven and try again.
E8	A&D	Control board problem.
E9	A&E	Latch switch problem.
E10	B&D	Control board problem.
E11	A&F	CT oven – latch switch problem
E12	A&E	CT ovens – latch switch problem
E13	A&C	CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data).
E14	A&E	Latch switch problem.
E15	B&D	Control board problem.

ERROR CODE NOTES	DESCRIPTION OF PROBLEM
A	Turns heat off on the failed oven only; microwave not affected.
B	Turns all heat off; microwave not affected.
C	Disables the CLEAN mode in both ovens; allows COOK and microwave.
D	Error will remain in the display until oven is repaired and powered back up. No error tones.
E	Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN.
F	Tweaking clears to “—“ for retry.
G	Clears when the oven temperature is less then the runaway temperature with the selector switch off.
H	Can be cancelled by tweaking if a good sensor is detected.
I	Cleared with a mode change.
J	Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door.
K	Turns heat and microwave off.
L	If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message.