THERMADOR Error Code E11
Professional Ranges Models: PDR30/36/48…PRG30/36/48
ERROR CODE | DESCRIPTION | RESOLUTION |
CODE E11 | Turns heat off on failed oven only, micro not affected. Tweaking clears to “—” for retry. Turns heat off on failed oven only, micro not affected. | CT oven; latch switch problem |
The control continuously keeps an eye on system specifications for control and stove failings and reports a fault code when a system issue is found. The control uses the ovens blue “on light” and also oven “home heating light” to report an identified mistake code. The control will remain to flash the lights in the proper series as long as the mistake exists.
Discovery of a mistake does not prevent the capacity of the control to remain to work if the fault is not critical for the designated operation. As an example: If the range door lock is defective, the variety will certainly remain to cook because the fault would only avoid the range from self-cleaning.
HOW TO TRANSLATE CODES
When a mistake occurs, the control will flash heaven stove “on light” and the Blue “home heating light” sequentially to show the fault. The fault codes have two numbers, these numbers are translated by the number of times the lights blink. The stove “on light” will blink indicating the very first number, as well as the “heating light” will blink suggesting the second number.
EXAMPLE:
Mistake E9 is … No Air conditioning Fans. The code is 43. The stove “on light” will certainly blink four times, after that the “heating light” will flash 3 times, then pause. The sequence will after that duplicate as long as the fault is present.
MISTAKE CODES FOR STOVES WITH DREEFS CONTROL
The complying with chart shows the error codes that can be shown in the Oven/Selector home window throughout specific stove breakdowns. A few of the error messages can be cleared by carrying out the adhering to steps:
- Turn the selector knob to OFF
2.”Modify” the oven by transforming the selector handle slightly to the left (counterclockwise). This may quit the blinking message/beeping and also clear the home window. - For errors E1, E9, E11, E12 as well as E13, the power supply mosting likely to the even need to be switched off for a little while, as well as back on once more.
- If a mistake stays shown when the selector switch is OFF, and also after trying to get rid of the screen, as received actions 2 as well as 3, switch off the power going to the oven, as well as describe the graph listed below to aid you discover the issue.
ERROR MESSAGE | ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
E1 | C&E | Control board problem. |
E2 | G&K | Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F). |
E3 | A&H | Open oven temperature sensor (>5000 Ω). |
E4 | A&H | Shorted oven temperature sensor (<5000 Ω). |
E5 | K&D | Control board too cold, too hot, or defective. |
E6 | C&J | Control board problem. |
E7 | A&I | Illegal temperature display. Turn off oven and try again. |
E8 | A&D | Control board problem. |
E9 | A&E | Latch switch problem. |
E10 | B&D | Control board problem. |
E11 | A&F | CT oven – latch switch problem |
E12 | A&E | CT ovens – latch switch problem |
E13 | A&C | CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data). |
E14 | A&E | Latch switch problem. |
E15 | B&D | Control board problem. |
ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
A | Turns heat off on the failed oven only; microwave not affected. |
B | Turns all heat off; microwave not affected. |
C | Disables the CLEAN mode in both ovens; allows COOK and microwave. |
D | Error will remain in the display until oven is repaired and powered back up. No error tones. |
E | Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN. |
F | Tweaking clears to “—“ for retry. |
G | Clears when the oven temperature is less then the runaway temperature with the selector switch off. |
H | Can be cancelled by tweaking if a good sensor is detected. |
I | Cleared with a mode change. |
J | Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door. |
K | Turns heat and microwave off. |
L | If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message. |