THERMADOR Error Code E10
Professional Ranges Models: PDR30/36/48…PRG30/36/48
ERROR CODE | DESCRIPTION | RESOLUTION |
CODE E10 | Turns all heat off, micro not affected. Error will remain in display until repaired and powered up. No error tones. | Repair the electronic range control (also called clock or ERC) |
The control continuously keeps track of system specifications for control as well as stove failures and reports a mistake code when a system trouble is detected. The control makes use of the ovens blue “on light” and oven “home heating light” to report a found fault code. The control will continue to blink the lights in the appropriate series as long as the fault exists.
Discovery of a fault does not prevent the ability of the control to continue to operate if the fault is not important for the intended operation. For example: If the array door lock is faulty, the range will remain to prepare since the mistake would only avoid the variety from self-cleaning.
HOW TO ANALYZE CODES
When a mistake takes place, the control will certainly blink heaven stove “on light” and heaven “home heating light” sequentially to show the mistake. The fault codes have 2 numbers, these numbers are interpreted by the variety of times the lights blink. The stove “on light” will certainly blink suggesting the very first number, and also the “home heating light” will blink showing the 2nd number.
INSTANCE:
Error E9 is … No Cooling Followers. The code is 43. The oven “on light” will flash 4 times, after that the “heating light” will certainly blink 3 times, after that pause. The sequence will certainly then duplicate as long as the mistake exists.
MISTAKE CODES FOR OVENS WITH DREEFS CONTROL
The following chart shows the mistake codes that can be presented in the Oven/Selector home window throughout certain stove breakdowns. Some of the error messages can be cleared by carrying out the complying with actions:
- Turn the selector handle to OFF
2.”Fine-tune” the stove by transforming the selector handle slightly to the left (counterclockwise). This might stop the flashing message/beeping as well as clear the home window. - For errors E1, E9, E11, E12 and E13, the power supply mosting likely to the even need to be turned off temporarily, as well as back on once more.
- If a mistake remains shown when the selector button is OFF, and after trying to get rid of the screen, as shown in actions 2 and also 3, switch off the power mosting likely to the stove, as well as refer to the graph below to assist you locate the trouble.
ERROR MESSAGE | ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
E1 | C&E | Control board problem. |
E2 | G&K | Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F). |
E3 | A&H | Open oven temperature sensor (>5000 Ω). |
E4 | A&H | Shorted oven temperature sensor (<5000 Ω). |
E5 | K&D | Control board too cold, too hot, or defective. |
E6 | C&J | Control board problem. |
E7 | A&I | Illegal temperature display. Turn off oven and try again. |
E8 | A&D | Control board problem. |
E9 | A&E | Latch switch problem. |
E10 | B&D | Control board problem. |
E11 | A&F | CT oven – latch switch problem |
E12 | A&E | CT ovens – latch switch problem |
E13 | A&C | CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data). |
E14 | A&E | Latch switch problem. |
E15 | B&D | Control board problem. |
ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
A | Turns heat off on the failed oven only; microwave not affected. |
B | Turns all heat off; microwave not affected. |
C | Disables the CLEAN mode in both ovens; allows COOK and microwave. |
D | Error will remain in the display until oven is repaired and powered back up. No error tones. |
E | Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN. |
F | Tweaking clears to “—“ for retry. |
G | Clears when the oven temperature is less then the runaway temperature with the selector switch off. |
H | Can be cancelled by tweaking if a good sensor is detected. |
I | Cleared with a mode change. |
J | Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door. |
K | Turns heat and microwave off. |
L | If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message. |