Sub-Zero is the embodiment of design as well as performance refrigeration. It isn’t just an appliance, your Sub-Zero is an essential element of your ideal kitchen area. It makes good sense that you would not want to trust your refrigerator to just any kind of home appliance repair work firm. You desire a team of Sub-Zero fridge repair service experts that can shield your investment while giving the premium service you should have.
It Is Fixed Home Appliance Fixing is the company you ought to rely on with every one of your Sub-Zero repair service needs. Our technicians specialize in Sub-Zero solution so you can rely on that we have the abilities to do the job right.
HOW TO USE THE ERROR CODE TROUBLESHOOTING OVERVIEW
Mistake Codes suggest issues registered by certain components. If mistake codes are signed up, they will appear prior to temperature readings while in Diagnostic Mode.
KEEP IN MIND: If Error Codes appear with a flashing “SERVICE” annunciator before initiating Diagnostic Setting, the device experienced excessive compressor run problem that might or might not be related to the Error Codes presented
To launch Diagnostic Setting, press as well as hold either COLDER secret, after that push the POWER key, after that launch both keys. Currently, examine to see if Error Codes are present, being sure to toggle with all error and temperature level readings by pressing either COLDER key or either WARMER trick. (See Mistake Code Table Below).
If Error Codes show up throughout Diagnostic Mode, comply with the Error Code Troubleshooting Guide on the complying with page. The left column of the troubleshooting overview lists the mistake codes. The details in the best column discusses what examinations to do and/or what action to require to deal with the mistake.
KEEP IN MIND: If error codes are observed in analysis mode, a non-flashing SERVICE annunciator will certainly appear on the LCD when Diagnostic Mode finishes, indicating mistake codes are still kept. Mistake Codes must be cleared from the digital control memory by hand. To remove the non-flashing SOLUTION annunciator as well as the mistake codes, the issue should be corrected and also the unit has to be ON, after that:.
- On a design UC-24C: Press the Fridge Freezer WARMER as well as COLDER tricks for fifteen (15) seconds.
- On a version UC-24B, UC-24R, or UC-24RO: Press the Refrigerator WARMER and COLDER tricks for fifteen (15) seconds.
Error Code Table
CODE | INDICATION |
05 | Refrig. cabinet thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
06 | Refrig. evaporator thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
07 | Freezer cabinet thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
08 | Freezer evaporator thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
20 | Defrost under-heat with no voltage feedback through Gray/White wire at defrost start |
21 | Defrost overheat |
22 | No voltage feedback through Gray/White wire at defrost start |
23 | Defrost overheat with no voltage feedback through Gray/White wire at defrost start |
24 | Defrost under-heat |
30 | N/A |
40 | Excessive Freezer Compressor Run |
50 | Excessive Refrigerator Compressor Run |
Error Code | CAUSE | SOLUTION |
Error Code SU | Wiring or Defrost Issue | A Sub-Zero appliance repair technician will need to check the wiring to ensure all parts are working and connected properly. |
Error Code SU
A. If “EE” for fridge area was displayed as well as “SOLUTION” flashing, inspect the following:.
- Thermistor electrical connections and also continuity from thermistor to J5 on control panel. Reconnect/ repair service.
- Resistance of thermistor– 30,000 to 33,000 ohms at 32 ° F( 0 ° C). Replace if malfunctioning. B. If “EE” for fridge compartment was NOT displayed, issue is periodic thermistor mistake:.
- Door not closing properly. Right door closing trouble.
- Inspect light switch, circuitry & electrical connections. Repair work wiring/ links or change button.
- Inspect thermistor electrical connections and also continuity at J5 on control panel. Reconnect/ fixing.
- Examine resistance of thermistor– 30,000 to 33,000 ohms at 32 ° F (0 ° C). Change if faulty.
C. If “EC 05” and also “SERVICE” were blinking prior to launching diagnostic setting, device also experienced excessive compressor run problem that may or may not be connected with the “05” Mistake Code. See Mistake Code 50 Test/Actions.