Sub-Zero is the epitome of style as well as efficiency refrigeration. It isn’t simply a home appliance, your Sub-Zero is an essential element of your perfect cooking area. It makes good sense that you wouldn’t intend to trust your refrigerator to just any type of home appliance repair work business. You want a team of Sub-Zero fridge repair work professionals that can safeguard your financial investment while supplying the premium service you should have.
It Is Fixed Device Fixing is the firm you need to rely on with all of your Sub-Zero fixing demands. Our service technicians concentrate on Sub-Zero service so you can trust that we have the skills to get the job done right.
HOW TO USAGE THE ERROR CODE TROUBLESHOOTING OVERVIEW
Error Codes show issues registered by details components. If mistake codes are registered, they will appear before temperature level analyses while in Diagnostic Setting.
KEEP IN MIND: If Mistake Codes appear with a blinking “SERVICE” annunciator before launching Diagnostic Mode, the system experienced too much compressor run condition that might or may not be connected with the Error Codes presented
To launch Diagnostic Setting, press and hold either COLDER secret, then push the POWER secret, then release both tricks. Currently, examine to see if Mistake Codes exist, making sure to toggle via all error and temperature analyses by pushing either COLDER key or either WARMER trick. (See Error Code Table Below).
If Mistake Codes show up during Diagnostic Setting, follow the Error Code Troubleshooting Overview on the following page. The left column of the troubleshooting overview provides the error codes. The info in the right column describes what examinations to execute and/or what action to take to deal with the error.
KEEP IN MIND: If mistake codes are observed in diagnostic mode, a non-flashing SOLUTION annunciator will certainly appear on the LCD when Diagnostic Mode finishes, suggesting mistake codes are still kept. Mistake Codes have to be gotten rid of from the digital control memory by hand. To get rid of the non-flashing SOLUTION annunciator as well as the error codes, the problem has to be fixed and the system must be ON, after that:.
- On a model UC-24C: Press the Freezer WARMER and also COLDER tricks for fifteen (15) secs.
- On a model UC-24B, UC-24R, or UC-24RO: Press the Fridge WARMER as well as COLDER keys for fifteen (15) secs.
Error Code Table
CODE | INDICATION |
05 | Refrig. cabinet thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
06 | Refrig. evaporator thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
07 | Freezer cabinet thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
08 | Freezer evaporator thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
20 | Defrost under-heat with no voltage feedback through Gray/White wire at defrost start |
21 | Defrost overheat |
22 | No voltage feedback through Gray/White wire at defrost start |
23 | Defrost overheat with no voltage feedback through Gray/White wire at defrost start |
24 | Defrost under-heat |
30 | N/A |
40 | Excessive Freezer Compressor Run |
50 | Excessive Refrigerator Compressor Run |
Error Code | CAUSE | SOLUTION |
Error Code 20 | Defrost underheat | This error may indicate an issue with the wiring, defrost heater, defrost terminator, or refrigerator control board. If you receive this error, contact your local Sub-Zero repair service for assistance. |
Mistake Code 05.
A. If “EE” for fridge compartment was shown as well as “SERVICE” flashing, check the following:.
- Thermistor electric links and continuity from thermistor to J5 on control panel. Reconnect/ repair work.
- Resistance of thermistor– 30,000 to 33,000 ohms at 32 ° F( 0 ° C). Replace if defective. B. If “EE” for fridge area was NOT showed, trouble is periodic thermistor mistake:.
- Door not closing properly. Correct door closing trouble.
- Check light button, electrical wiring & electrical connections. Repair work wiring/ links or change button.
- Examine thermistor electric links and also continuity at J5 on control panel. Reconnect/ fixing.
- Inspect resistance of thermistor– 30,000 to 33,000 ohms at 32 ° F (0 ° C). Replace if malfunctioning.
C. If “EC 05” as well as “SOLUTION” were flashing before launching analysis setting, unit also experienced too much compressor run condition that may or may not be connected with the “05” Mistake Code. See Mistake Code 50 Test/Actions.