Sub-Zero is the embodiment of design as well as efficiency refrigeration. It isn’t just a device, your Sub-Zero is an essential element of your best cooking area. It makes sense that you would not wish to trust your refrigerator to simply any device repair service business. You want a group of Sub-Zero refrigerator fixing professionals that can secure your financial investment while offering the premium service you are entitled to.
It Is Fixed Device Repair is the company you need to rely on with every one of your Sub-Zero repair service needs. Our technicians specialize in Sub-Zero service so you can rely on that we have the skills to finish the job right.
HOW TO USE THE MISTAKE CODE TROUBLESHOOTING OVERVIEW
Mistake Codes suggest issues registered by particular elements. If error codes are signed up, they will show up before temperature analyses while in Diagnostic Mode.
NOTE: If Mistake Codes appear with a flashing “SERVICE” annunciator before starting Diagnostic Setting, the unit experienced too much compressor run condition that may or may not be associated with the Mistake Codes showed
To launch Diagnostic Setting, press as well as hold either COLDER secret, after that push the POWER trick, then launch both secrets. Currently, inspect to see if Mistake Codes exist, being sure to toggle with all error and temperature level analyses by pushing either COLDER essential or either WARMER secret. (See Mistake Code Table Below).
If Error Codes show up during Diagnostic Setting, adhere to the Mistake Code Troubleshooting Guide on the adhering to page. The left column of the troubleshooting overview lists the error codes. The info in the appropriate column describes what tests to perform and/or what action to require to remedy the error.
KEEP IN MIND: If error codes are observed in analysis mode, a non-flashing SERVICE annunciator will show up on the LCD when Diagnostic Mode finishes, showing mistake codes are still kept. Mistake Codes should be cleared from the digital control memory by hand. To get rid of the non-flashing SERVICE annunciator as well as the mistake codes, the issue must be remedied and the unit has to be ON, then:.
- On a design UC-24C: Press the Freezer WARMER and COLDER tricks for fifteen (15) seconds.
- On a model UC-24B, UC-24R, or UC-24RO: Press the Refrigerator WARMER as well as COLDER keys for fifteen (15) seconds.
Error Code Table
CODE | INDICATION |
05 | Refrig. cabinet thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
06 | Refrig. evaporator thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
07 | Freezer cabinet thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
08 | Freezer evaporator thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
20 | Defrost under-heat with no voltage feedback through Gray/White wire at defrost start |
21 | Defrost overheat |
22 | No voltage feedback through Gray/White wire at defrost start |
23 | Defrost overheat with no voltage feedback through Gray/White wire at defrost start |
24 | Defrost under-heat |
30 | N/A |
40 | Excessive Freezer Compressor Run |
50 | Excessive Refrigerator Compressor Run |
Error Code | CAUSE | SOLUTION |
Error Code 08 | Inconsistent temperature readings in the refrigerator or freezer cabinet. | The issue may be caused by loose or faulty connections between the thermistor and the control board, or it may mean the thermistor is faulty. Refer to your owner’s manual to locate the thermistor, and ensure the wires between the thermistor and control panel are securely connected. If you do not have your original manual, you may be able to find a digital copy online. If the connections are secure, the thermistor and control panel will need to be tested to ensure functionality. Testing requires the use of a multimeter. You may need the assistance of a specialist trained in Sub-Zero refrigerator repair to diagnose and replace the faulty components. |
Error Code 08
A. If “EE” for refrigerator area was displayed as well as “SOLUTION” blinking, inspect the following:.
- Thermistor electric connections as well as connection from thermistor to J5 on control panel. Reconnect/ repair work.
- Resistance of thermistor– 30,000 to 33,000 ohms at 32 ° F( 0 ° C). Replace if defective. B. If “EE” for refrigerator compartment was NOT showed, problem is recurring thermistor error:.
- Door not shutting correctly. Appropriate door closing trouble.
- Inspect light button, circuitry & electric links. Repair circuitry/ links or replace switch.
- Inspect thermistor electric connections and continuity at J5 on control panel. Reconnect/ fixing.
- Check resistance of thermistor– 30,000 to 33,000 ohms at 32 ° F (0 ° C). Replace if defective.
C. If “EC 05” and “SERVICE” were blinking prior to initiating analysis mode, unit additionally experienced extreme compressor run problem that may or may not be connected with the “05” Error Code. See Mistake Code 50 Test/Actions.